How high is the basketball hoop from the floor? Standard size basketball backboard. Free space under the shield

basketball playground

The playing area must be a flat rectangular hard surface without any obstacles.
For the main official FIBA ​​competitions, as well as for new playing fields under construction, the dimensions, measured from the inside edge of the boundary lines, must be 28 meters long and 15 meters wide. For all other competitions, the relevant FIBA ​​structures, such as the Zonal Commission or National Federations, have the right to approve existing playing fields with minimum dimensions 26 meters long and 14 meters wide.

Ceiling.
The height of the ceiling or the distance to the lowest object above the playing area must be at least 7 meters.

Lighting.
The playing surface must be evenly and adequately lit. Light sources must be located where they will not interfere with Players and Officials.

Lines.
All lines must be painted in the same color (preferably white), 5 cm wide and clearly visible.

front and side lines.
The playing area must be limited by two front (on the short sides of the site) and two side (on the long sides of the site) lines. These lines are not part of the court. The playing court must be at least 2 meters away from any obstacles, including the team bench.

Central line.
The center line is applied parallel to the end lines from the middle of the side lines and should protrude 15 cm beyond each side line.

Central circle.
The center circle is marked in the center of the court and has a radius of 1.80 m measured to the outer edge of the circle. If the center circle is painted a different color, it must be the same color as the restricted areas.

Free throw lines, restricted areas and free throw areas.

The free throw line is applied parallel to each end line. Its far edge is at a distance of 5.80 m from the inner edge of the end line, its length must be 3.60 m. Its middle must be on an imaginary line connecting the midpoints of the two end lines.
Restricted areas are designated areas on the court, bounded by the end lines, free throw lines and lines that start from the end lines. Their outer edges are 3 m from the middle of the end lines and end at the outer edge of the free throw lines. These lines, excluding the end lines, are part of the restricted area. The restricted areas may be painted a different color, but they must be the same color as the center circle.
Free throw areas are limited areas extended towards the playing court in semicircles with a radius of 1.80 m, the centers of which are located in the middle of the free throw lines. The same semicircles must be drawn in dotted lines within the restricted areas.
The places along the free throw areas taken by Players during free throws are marked as shown in the diagram.

Three-point shooting zone.

A team's three-point field goal area is the entire playing court, except for the area near the opponent's basket, limited by:
two parallel lines, starting from the end line at a distance of 6.25 m from the point on the court obtained at the intersection with it of a perpendicular lowered from the center of the opponent's basket. The distance from this point to the inner edge of the middle of the end line is 1.575 m.
A semicircle with a radius of 6.25 m to the outer edge of its line, centered on the same point as above, until it joins the parallel lines.

Shields.

Shields must be made of a suitable transparent material (preferably tempered safety glass) which is a single piece.
If they are made of other opaque material(s), they must be painted white.
The dimensions of the shields should be: 1.80 m horizontally and 1.05 m vertically.
All lines on the shield must be marked as follows:
- white if the shield is transparent.
— in black in all other cases.
- 5 cm wide.
The front surface of the shields must be smooth.

Shield layout.
Shields must be rigidly mounted as follows:
- at both ends of the court at right angles to the floor, parallel to the end lines.
— the vertical center line on their front surface, extended down to the floor, must touch a point on the floor lying 1.20 m from the inner edge of the middle of each end line, on an imaginary line drawn at right angles to that end line.

Shield supports.

The shield supports should be designed as follows:
— front part structures (including upholstery) must be placed at least 2.00 m from the outer edge of the end line, painted in a bright color contrasting with the color of the walls, so as to be clearly visible to the Players.
- the shield support must be so attached to the floor that it cannot be displaced.
— any structure to which the shield is attached must be upholstered with soft material behind the shield along the bottom surface of the structure at a distance of 1.20 m from the front surface of the shield.
- the minimum thickness of the upholstery should be 5 cm. It should have the same density as the upholstery of the panels.
- all backboard support structures must be completely upholstered with soft material to a height of at least 2.15 m on the surface from the side of the site. The minimum thickness of the upholstery must be 10 cm.

Baskets.

Baskets consist of rings and nets.

Rings.
Material - durable steel, inner diameter 45 cm and painted orange.
The metal bar of the ring must have a minimum diameter of 16 mm and a maximum diameter of 20 mm. On the bottom of the ring there must be devices for attaching nets, such as to prevent injury to the fingers.
The mesh must be attached to the ring at twelve equally spaced points along the entire perimeter of the ring. Net attachment devices must not have sharp edges or crevices that the Player's fingers could get into.
The ring is attached to the structure supporting the basket in such a way that no force applied to the ring is transmitted directly to the shield. Therefore, there should be no direct contact between the ring and the device that secures the ring to the shield and the shield. However, the gap must be small enough that fingers cannot get into it.
The upper edge of each ring should be located horizontally at a height of 3.05 m above the surface of the site at an equal distance from the vertical edges of the shield.
The nearest point of the inner part of the ring should be located at a distance of 15 cm from the front surface of the shield.
You can use rings with a shock absorber.

Grids.
Made of white cord and designed to hold the ball momentarily as it passes through the basket. The net length must be at least 40 cm and not more than 45 cm.
Each mesh should have 12 loops for attaching to the ring.
The top sections of the mesh must be sufficiently rigid to prevent:
Overlapping of the mesh on the ring and its possible entanglement.
The ball getting stuck in the net or thrown back out of the basket by the net.

Official Basketball Rules

Related articles:

Video lesson Technique of jumping from two legs

Video lesson on shooting technique in basketball

What children should know and be able to play basketball at the Youth Sports School

Control and transfer standards for basketball players in the Youth Sports School

Basketball backboard and hoop are a must basketball court. The world has adopted standards regarding these elements: they were established by the International Basketball Federation.

A basketball backboard is a rectangular or square panel on which the hoop is fixed. The shield is equipped with a mount for mounting on a pole or hanging on the wall: rigid mounting is required so that the product does not wobble or move. The size of the product is 1.8x1.05 meters, while the distance from its edge to the floor should be 2.9 meters. The NBA has set the following standards: the size of the backboard is 72 x 42 inches. There should be two shields, they are installed at opposite ends of the field, the material is durable and resistant to shock (for example, tempered glass, acrylic, wood). The surface is marked with lines, it must be smooth. Non-stationary basketball backboard models with a net use the same mounting elements as the brackets for hanging punching bags. This allows you to endure big weight product and fasten it securely.

What should a basketball hoop look like?

The ring or basket is a metal (steel) circle, which is covered with a mesh without a bottom. This element should be installed at a distance of 3.05 meters from the floor and 0.15 meters from the bottom edge of the shield.

How to make a basketball backboard and a ring in the yard, what sizes and what can be done?

The inner diameter can vary from 45 to 45.7 centimeters. The basketball hoop is painted in a bright color, most often orange. The load on the basket should not be transferred to the shield, so special attention must be paid to the installation of the product.

Front line and its dimensions

Do you want to play games only on high-quality venues? Alfasport has been manufacturing equipment for many years sports centers, stadiums, fitness clubs. We worked with the largest facilities in Minsk and Belarus, we have our own production and a solid reputation!

Choose, call and order!

Catalog of articles about sports and a healthy lifestyle

How to make a basketball hoop

An obligatory sign of such famous game like basketball, is a basketball hoop with a net. You can absolutely build this device in your yard, making a shield and a homemade one from improvised materials. ring from thick wire. But if you decide to practice your playing skills more masterfully, you should know what are the requirements for the design of a basketball hoop. Keep these instructions in mind when making sports equipment.

You will need

• - metal rod with a diameter of 16-20 mm
• - metal plate
• - white cord

Instruction

1. The expertly crafted basket consists of a basketball hoop and a net. The design of the ring is clearly defined by the relevant rules of the game. The material for the ring is strong iron. The inner diameter of the ring is 45 cm. The ring should be orange in color. The diameter of the rod from which you have to make ring, must be at least 16 mm and not more than 20 mm.

2. Bottom part The basketball hoop has attachments for attaching the net. The design of such devices should prevent injury to the fingers.

3. The basketball net is attached to the hoop at twelve points along each hoop perimeter. These points must be located at an equal distance from each other. Net attachment devices must not have sharp edges or gaps where the player's fingers could get caught.

4. The fastening of the ring to the structure supporting the basket is done in such a way that any force applied to the ring cannot be transferred unconstrainedly to the shield. direct contact between ring m and a fastening device should not be. At the same time, the gap should be quite small so that the player's fingers cannot get into it.

5. The upper edge of the ring is located horizontally at a height of 3.05 m above the surface of the playing area. The ring must be identically spaced from the vertical edges of the shield. The nearest point of the inner surface of the ring is located 15 cm from the front surface of the shield.

6. It is not forbidden to use shock-absorbing basketball ring. It is equipped with an appropriate spring mechanism that allows the ring to deviate 30 degrees and return to its original position.

7. A few words about the net that you have to make complete with a basketball ring m. It is allowed to make it from a white cord. It should be large enough to momentarily stop a basketball passing through the basket from above. The length of the basketball net is 40-45 cm. The net must have twelve loops for attaching to the ring.

The top segments of the net are made rigid to prevent the net from becoming tangled or entangled to an acceptable extent, as well as the ball getting stuck. The net must not allow the ball to be thrown back out of the basket for no reason.

Standard basketball backboard sizes

DIY basketball stands

Basketball stands can be made by hand, or you can buy from us easier and faster.

There is currently a large number of wide variety of designs basketball racks. Their choice is determined by the conditions and the place of installation. For halls with a length of less than 30 m, wall hangings are usually used, on outdoors and in halls longer than 30 m - floor and hanging racks. For school halls, the length of which usually does not exceed 24 m, only wall racks may be of interest, and for open areas - floor racks.

Basketball posts for open areas (Fig. 173, 174, 175) are a tubular welded truss, dug into the ground or loosely resting on the ground. In the latter case, stability is created by means of load balances placed on the base of the truss. Such racks (they are called portable) are convenient in that they can be moved, freeing up space for other sports events, for pouring rollers, etc.

Basketball stands consist of a truss, a wooden (or organic glass) backboard and a ring with a net.

To make a farm, which will then be reinforced in the ground, it will take 45 m of water and gas pipes with a diameter of 1 / * inch, 21 m of pipes with a diameter of 3-4 inches and sheet steel (for washers) 8 mm thick - 0.5 m2.

The depth of the farm into the ground depends on the freezing of the soil in the area, but should not be less than 700 mm. The truss is fixed on concrete bases (section size 0.5 X 0.5 m) with a depth of at least 1 m. When concreting, the vertical position of the shield should be ensured. To do this, the support flanges are installed inside the dug pits on brick posts 300 mm high, and the truss is supported by a prop. By adjusting the height of the support, a position is achieved in which the mounting shield flanges do not reach the vertical position by 2-3 ° '. In this case, the supporting flanges of the truss must rest on the brick columns with the entire surface. If this does not happen, it is necessary to place steel linings under the flanges.

Having adjusted the position of the farm, the pit is poured with cement mortar flush with the ground. The farm remains standing with props for at least 3-5 days. After this period, the supports are removed and the shield is hung. In this case, the truss, under the weight of the shield and its own, will lean forward somewhat and the shield flanges will take a strictly vertical position. Using the oval holes in the flanges, the backboard is installed straight, without distortion, and the lower edge of the backboard should be 2.75 m from the surface of the playing area.

The shield is made of dry pine boards 30 mm thick, connected into a spike, and framed with a frame 30 mm thick and 75 mm wide and bars 45 and 120 mm, respectively. To increase rigidity, it is allowed to place a vertical bar in the middle part of the shield of the same dimensions as the outer bars. The parts are connected with K-17 glue.

Shield dimensions: length - 1800 mm, height - 1200 mm.

In addition to the standard ones, you can use simplified shields. They are assembled from dry boards 20-30 mm thick, butted together and connected by four vertical bars 160 mm wide and 60 mm thick. The bars are fastened to the boards with screws 5-6 mm in diameter and 60-75 mm long.

Front surface basketball backboard must be carefully crafted, well sanded and painted with white oil paint. The back of the board is soaked with hot drying oil. Along the entire perimeter, the shield is bordered with a black strip 50 mm wide, and in the middle part, at a height of 250 mm from the bottom edge, a rectangle measuring 600 X 450 mm is applied. Line thickness

rectangle - 50 mm.

To connect the shield to the truss, standard bolts with a diameter of 10-12 mm and a length of 75-90 mm are used (depending on the thickness of the shield). The heads of the bolts are flush and, after installation, are painted over with paint to match the color of the shield.

Rings for hanging the mesh can be made in a normal or simplified design.

The ring of a simplified design is a circle with an inner diameter of 450 mm, rolled from a bar with a diameter of 20 mm. The circle is connected by a metal rod with a diameter of 30-35 mm with a round flange, which is attached to the shield with three bolts with a diameter of 10 mm. On the circle for attaching the mesh, through holes (11 or 22) with a diameter of 5 mm are provided or brackets of various configurations are welded.

A simplified ring can be successfully used in schools for primary education. However, it should be remembered that it is not rigid enough and vibrates when hit by the ball.

Basketball backboard with your own hands. Made of Metal Project

The rebound of the ball from such a ring is unstable.

The normal design ring is devoid of this drawback, but its manufacture is more difficult due to the introduction of additional struts, a plate bracket, as well as a large number of welding operations.

I.P. Mokhov, S.N. Abelson

Sports equipment and supplies for schools

Publishing house "Enlightenment" Moscow 1967

01. First, I sit down at the computer and sketch out a drawing for attaching the shield and the pole itself.

It was originally planned to put the ring in another place and pull it with a solid hitch to the nearest tree. But there turned out to be a lot of roots and they decided to put them in free flight and without a screed, which is why the ring in the upper part of the column remained rudimentary only in the drawing. Diagonals that are not in the drawing (green) have also been cancelled. We decided that the rigidity of the wooden shield and metal fasteners would be enough not to "walk".

Also on the course I changed the way of strengthening the outrigger knee. Not with a corner as in the drawing, but with two stripes on the sides, see the photo below.

A profile of 5 cm was used for the pole, for a bracket strung on a pole - 6 cm. A strip is welded inside so as not to play.
Everything that adjoins the wooden shield is a 25 mm corner.

Important: the ring should be universal for both adults and children of different heights. Therefore, a height offset system was made.

02. The main large elements are welded: a pillar, a knee, two stepson solid fuel boosters. The upper edge of the pillar and stepchildren is bevelled: for rainfall and for beauty.

03. More different views

04.

05. There it is a strip welded inside the elbow pipe. At the top of the hole.

06. The shield fixing system has been completed. No, this is not a bottle of Zhatetsky Gus beer, this is gasoline.

What is the size and layout of the basketball backboard? At what height is it attached?

Stepchildren are welded. There was an error in the calculations. It was assumed that the stepchildren would strengthen the pillar from swinging, but they were attached lower than necessary. Further in the photo you will see that they protrude quite a bit from the ground. It would be possible to raise 30-40 cm higher. And now, nevertheless, the pillar sways during the game.

08. The heels are welded into the part that goes underground.

09.

10. Everything is painted

11.

12. Fossa

13. It will stand like this for a couple of days and you can continue. there was no putty for metal, to putty the seams. The putty was bought in addition, puttied and repainted a little later.

14. Up!

15. Shield assembly.

16. Done!

17. Now the ring is at its lowest height. Even lower than calculated, because one hole is not used (see the vacant thumb screw). Altitude change occurs with the help of one man-power on a stepladder.

18.

19. Open Championship village basketball started!

http://print-design.livejournal.com/

Oh sport, you are the world!

There is nothing at the dacha, only bending metal, fumbling shish kebab, drinking beer.
It is necessary to do sports both by ourselves and by children.

True, for this you will first have to "bend the metal" and celebrate this matter with beer and barbecue.

In the next series of the project "Made of Metal" - to make a basketball backboard.
Joint work of me and my father.

Batko studied the standards for the height and dimensions of a basketball backboard, made a wooden backboard himself, painted it, made wing screws, and installed a pole. Well, he additionally made critical remarks to the metal part.

I - invented the entire metal part and welded the metal.

01. First, I sit down at the computer and sketch out a drawing for attaching the shield and the pole itself.

It was originally planned to put the ring in another place and pull it with a solid hitch to the nearest tree. But there turned out to be a lot of roots and they decided to put them in free flight and without a screed, which is why the ring in the upper part of the column remained rudimentary only in the drawing. Diagonals that are not in the drawing (green) have also been cancelled. We decided that the rigidity of the wooden shield and metal fasteners would be enough not to "walk".

Also on the course I changed the way of strengthening the outrigger knee. Not with a corner as in the drawing, but with two stripes on the sides, see the photo below.

A profile of 5 cm was used for the pole, for a bracket strung on a pole - 6 cm. A strip is welded inside so as not to play.
Everything that adjoins the wooden shield is a 25 mm corner.

Important: the ring should be universal for both adults and children of different heights. Therefore, a height offset system was made.

02. The main large elements are welded: a pillar, a knee, two stepson solid fuel boosters. The upper edge of the pillar and stepchildren is bevelled: for rainfall and for beauty.

03. More different views

05. There it is a strip welded inside the elbow pipe. At the top of the hole.

06. The shield fixing system has been completed. No, this is not a bottle of Zhatetsky Gus beer, this is gasoline.

07. Stepchildren are welded. There was an error in the calculations. It was assumed that the stepchildren would strengthen the pillar from swinging, but they were attached lower than necessary. Further in the photo you will see that they protrude quite a bit from the ground. It would be possible to raise 30-40 cm higher. And now, nevertheless, the pillar sways during the game.

08. The heels are welded into the part that goes underground.

10. Everything is painted

12. Fossa

13. It will stand like this for a couple of days and you can continue. there was no putty for metal, to putty the seams. The putty was bought in addition, puttied and repainted a little later.

14. Up!

15. Shield assembly.

16. Done!

17. Now the ring is at its lowest height. Even lower than calculated, because one hole is not used (see the vacant thumb screw). Altitude change occurs with the help of one man-power on a stepladder.

19. The Basketball Village Open Championship has begun!

Women's basketball is a sport team game, its main purpose is to throw the ball into the basket of the opposing team. Those who earn the most points during the competition win. Only tall and fast girls are selected for basketball. It is believed that this sport is very useful, so it is included in the program. sports training for schools.

Women's basketball - rules of the game

Experts believe that women's basketball:

• hones coordination;
• trains muscles and breathing;
• improves blood circulation;
• strengthens the nerves.

These characteristics made the game very famous, the first rules were invented by the American James Naismith in 1891. The teacher wanted to make gymnastics lessons more interesting, at first the teams just threw balls into fruit baskets. Only a year later, James formulated the basic rules, at first there were 13 of them. And the rules of women's basketball at the international level were adopted only in 1932, at the first congress International Federation basketball. The most extreme adjustments were made in 2004. The rules are simple:

1. Two groups compete, five participants from each.
2. The goal of the game is to throw the ball into someone else's basket and not let it be thrown into your own.
3. The game is played only with hands, kicking or stopping the ball is considered a violation.
4. With the same number of points, the judge adds time, and does so until a winner is determined.
5. 2 points are awarded for a close-range shot, 3 points for a long-range shot, and 1 point for a free throw.

Women's basketball - hoop height

Women's volleyball has become so popular due to the fact that it is the least traumatic. It also improves health with a variety of loads:

• walking and running;
• stops, turns, throws;
• jumping, catching and dribbling.

The height of the basketball hoop from the floor is 10 feet or 3.05 meters. The same standards apply to men's basketball. By sports standards, the basket is fixed at a distance of 0.15 meters from the low edge of the basketball backboard, and the basket itself is fitted on the hoop with a net that does not have a bottom. The lower edge of the basket is fixed at a distance of 3 meters 5 centimeters from the floor, this rule is common for both men's and women's teams. There are a few more important points:

1. The structure is placed in such a way that it is impossible to displace it, and the loads do not affect the position of the shield.
2. The correct distance from the floor to the top is measured by a specialist, because not only accuracy plays a role, but also the difference in slopes in one direction and the other.

How many quarters are there in women's basketball?

In basketball, "pure" time is counted, the game has from 2 to 4 periods or quarters, 12 minutes each. Breaks are given for two minutes. In numerous sports time is divided into halves, women's basketball rules are the same. The stopwatch starts only when the ball is in play, but if it flies out of the field, the timer is stopped. Full playing time is from 40 to 48 minutes, everything is decided by the rules.

How long is a quarter in women's basketball?

How long is a quarter in basketball? Each is given 10 minutes of time not falling out of the game, taking into account the breaks between them of 120 seconds. Only at the height of the game, between the second and third periods, 15 minutes are allocated for rest. But there are some deviations:

1. In Europe, a quarter has 10 minutes.
2. In America they play for 12 minutes.
3. In the NBA, the score is 12 minutes, but with timeouts and delays, it runs for about half an hour.

Ranking of women's basketball teams

Women's basketball is a sport where matches are no less exciting than men's, points and penalties are taken into account by the referee according to generally accepted world rules. To get the right to play in the most prestigious tournament, the Russian team this year played 6 matches with basketball players from Greece, Bulgaria and Switzerland. The women's basketball team managed to win the World Cup and the European Cup, topping the world rankings and displacing the former champions from Hungary.

Women's basketball - films

Most large quantity Basketball supporters live in America, where almost all the inhabitants of the country are familiar with this game. Due to such popularity, directors shot films about women's basketball often, and they are a success even at the global box office. The most famous films:

1. "Away match". The story of a coach who formed a team of black players and led them to champions.
2. "Season of Victory". A well-known coach in the past gets a chance to return to his favorite sport, but on one condition: it is necessary to prepare the women's team in such a way that the girls reach the highest level.
3. "Mighty Max". Coach history women's team Cathy Nash who manages to short term make the winners of tournaments out of weaklings-outsiders.

Basketball backboards and rings.

Buy mobile basketball backboards and rings The Schelde analogue is not a problem.

In the winter of 1891, students at the Youth Christian Association College in Springfield, Massachusetts, were bored in class. physical education forced to perform endless gymnastic exercises, which at that time were considered almost the only means of introducing young people to sports.

A humble college teacher named James Naismith found a way out of what seemed to be an impasse. On December 1, 1891, he tied two peach baskets to the railing of the balcony of the sports hall and, dividing eighteen students into two teams, offered them a game, the meaning of which was to throw more balls into the opponents' basket.

The idea for this game came to him in school years when the kids played the old game of duck-on-a-rock. The meaning of this game, popular at that time, was as follows: throwing a small stone, it was necessary to hit the top of another stone, larger in size, with it.

Quite pragmatically called "basketball" (English basket - basket, ball - ball), the game, of course, only remotely resembled the enchanting spectacle that we know under this name today. From a modern point of view, the actions of the teams would seem to us sluggish and inhibited, but the goal of Dr. Naismith was to create a team game in which a large number of participants could be involved at the same time, and his invention fully met this task.

It is not so important for basketball players where to play, score goals, pass passes, the main thing is to have the ball at hand and the target on the side of the imaginary enemy - a basketball backboard with a net.

A basketball backboard is the basis of any playing area - whether it's a playground, a school yard, gym or the whole stadium. We have a cantilever mounting of a street basketball backboard

The design of any basketball backboard (especially mobile ones) must be especially strong and durable.

The standard size of a basketball backboard for adults is 1.05x1.8m, the size of a streetball backboard is 1.0x0.9m, 1.2x0.8m, 1.3x0.9m.

A basketball backboard for an adult game is installed at the required standard height of 3.05 m, it can be steel frame with metal framed backboard plate for hanging basketball structures, ceiling and wall basketball trusses. Our company has been producing basketball backboards for competitions and trainings for a long time.

Prices are indicated from the gate of our production and do not include installation and delivery of equipment.

Below are wholesale prices.*

Game basketball backboard 1.05x1.8m (1.8x1.05m.) on a steel frame with a metal frame of the backboard plate, for sports grounds and halls. The shield plate is made of moisture-resistant plywood laminated with polymer (white shield, black markings), pcs. ASPORT0909-1.
Game basketball backboard 1.05x1.8m (1.8x1.05m.) on a steel frame with a metal frame of the backboard plate, for sports fields and halls. The shield plate is made of laminated plywood (dark colored shield, white markings), pcs. ASPORT0909. It can be completed with a ring and a grid.
Game basketball backboard 1050 x 1800 mm (1800 x 1050 mm.) on a steel frame with a metal frame of the backboard plate. The shield plate is made of white laminate, 16 mm thick, pcs. ASPORT0901. It can be completed with a ring and a grid.
Game basketball backboard 1050 x 1800 mm (1800 x 1050 mm.) on a steel frame with a metal frame of the backboard plate, pcs. The shield plate is made of Plexiglas (monolithic) 10 mm thick, pcs. ASPORT0903-1 It can be completed with a ring and a grid.
Game basketball backboard 1050 x 1800 mm (1800 x 1050 mm.) on a steel frame with a metal frame of the backboard plate. The shield plate is made of Plexiglas (monolithic) 8 mm thick, pcs. ASPORT0903 It can be completed with a ring and a grid.
Competitive basketball backboard 1050 x 1800 mm (1800 x 1050 mm.) On a steel frame with a metal framed shield plate. The shield plate is made of silicate glass 10 mm, according to FIBA ​​requirements, pcs. ASPORT0905 It can be completed with a ring and a grid.
Basketball training backboard, minibasketball (streetball) 1.05x0.8 m. ASPORT0904
Training basketball backboard, minibasketball (streetball) 1.05x0.8 m. (0.8x1.05 m.) hall, on a metal frame with a metal frame, transparent plexiglass 8 mm, light markings. In a set with a take-out frame of 0.5 m, set. ASPORT0910 Composed of: 2. Plexiglas shield 8 mm, 1.05x0.8 m ASPORT0904 - 1 pc. 3. Reinforced mass basketball hoop ASPORT1305-2 - 1 pc.
Basketball training board, minibasketball (streetball) 1.3-1.2 x 0.9-0.85m. for sports grounds and halls, dark color, light markings, set. ASPORT0906 Composed of: 1. take-out frame 0.5 m with fasteners only for walls made of monolithic brick or concrete ASPORT1705 - 1 pc. 2. shield 1.3-1.2 x 0.9-0.85m. dark laminated plywood ASPORT0907 - 1 pc. 3. Reinforced mass basketball hoop ASPORT1305-2, 1 pc. 4. mesh b/w mass ASPORT1501 - 1 pc.
Basketball training board, minibasketball (streetball) 1.3-1.2 x 0.9-0.85m. for sports grounds and halls, dark laminated plywood, light markings, without fixing to the wall/stem frame, pcs. ASPORT0907 It can be equipped with a take-out frame 0.5 - 1.2 m, a ring and a net.
Basketball training board, minibasketball (streetball), 1.3-1.2 x 0.9-0.85m. for sports grounds and halls, dark color, light markings. Without fastening to the wall. hung on gymnastic wall or on the wall of the hall, extension 5 cm, using hooks located on the back of the shield, set. ASPORT0908 Composed of: 1. shield 1.3-1.2 x 0.9-0.85m. dark laminated plywood ASPORT0907 - 1 pc. 2. Reinforced mass basketball hoop ASPORT1305-2, 1 pc.
Basketball training board, minibasketball (streetball), 1.3-1.2 x 0.9-0.85m. for sports grounds and halls, dark color, light markings. Without fastening to the wall. It is hung on the gymnastic wall or on the wall of the hall, 5 cm extension, using hooks located on the back of the backboard, pcs. ASPORT0912 It can be completed with a ring and a mass grid.
Basketball training board, minibasketball (streetball), 1.3-1.2 x 0.9-0.85m. hall, white, dark markings. It is hung on the gymnastic wall, with the help of hooks on the back of the shield. It is completed with a ring and a grid of mass. Without fasteners to the wall, including fasteners for the ring, to-t. ASPORT0913-1 Composed of: 1. streetball board ASPORT0913 white hall 1.3-1.2 x 0.9-0.85m. 1 PC. 2. Reinforced mass basketball hoop ASPORT1305-2, 1 pc., 3. mesh b / w mass ASPORT1501 - 1 pc. 4. Hooks located on the back of the backboard for hanging on the gymnastic wall. ASPORT0914 - 1 pc.
Basketball training board, minibasketball (streetball), 1.3-1.2 x 0.9-0.85m. for the hall, white, dark markings, reinforced on the back in the area of ​​the ring attachment. Hung on the wall of the hall, with the help of loops located on the back of the shield, pcs. ASPORT0913 It can be completed with a ring, a grid, including fasteners for the ring. Without fastening to the wall.
Basketball backboard 1.8x1.05m, mechanism for changing the height of the backboard (ring) to complete the take-out frames, pcs. ASPORT1208
Basketball backboard protection (protector), 0.3 x 1.8 x 0.0.6 m, for a full-size backboard, pcs. ASPORT1901
Basketball net for games, workshop, from a single braided cord, for ring No. 7, pcs. ASPORT1505
Basketball hoop, basket - shock-absorbed without a locking system, lightweight, safe fastening of the net without hooks according to the FIBA ​​standard, hoop - steel bar, coordinates of the mounting holes: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, in a set with fasteners on 60-70mm, the mesh is not included in the set, pcs. ASPORT1309
Basketball ring, basket - shock-absorbed without locking system, reinforced, safe fastening of the net without hooks according to FIBA ​​standard, hoop - steel bar, fixing hole coordinates: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, in a set with fasteners for 60-70mm, the mesh is not included in the set, pcs. ASPORT1308
Basketball hoop, basket - shock-absorbed with a locking system, secure net fastening without hooks according to FIBA ​​standard, including fasteners for 60-70mm, fixing hole coordinates: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, net in set not included, pcs. ASPORT1307
Basketball hoop, basket - shock-absorbed with a locking system, secure net attachment without hooks according to the FIBA ​​standard, including with fasteners for 60-70mm, the coordinates of the mounting holes according to the ASPORT standard and the FIBA ​​standard: from the top bar 25 mm, horizontally 126 mm, vertically 110-114 mm, the rest at the request of FIBA, the net is not included in the set, pcs. ASPORT1310
Basketball ring, basket - vandal-resistant, safe fastening of the net without hooks according to the FIBA ​​standard, hoop - steel bar, coordinates of the mounting holes: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, for a streetball backboard, in a set with fasteners on 30-40 mm, the mesh is not included in the set, pcs. ASPORT1306-2
Basketball ring, basket - vandal-resistant, safe fastening of the net without hooks according to the FIBA ​​standard, hoop - steel bar, coordinates of the mounting holes: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, for a full-sized backboard, in a set with fasteners on 60-70mm, the mesh is not included in the set, pcs. ASPORT1306-1
Basketball hoop, basket - massive reinforced, secure net attachment without hooks according to FIBA ​​standard, hoop - steel bar, mounting hole coordinates: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, for a full-size backboard, in a set with fasteners for 60-70mm, the mesh is not included in the set, pcs. ASPORT1305-1
Basketball hoop, basket, massively reinforced, secure net attachment without hooks according to FIBA ​​standard, hoop - steel bar, fixing hole coordinates: from the top bar 25 mm, horizontally 100 mm, vertically 65 mm, for a streetball backboard, in a set with fasteners for 30-40 mm, the mesh is not included in the set, pcs. ASPORT1305-2

* the prices indicated on this page are not a public offer and are provided for information only. In the case of the current value, the prices are WHOLESALE and are valid for the purchase of goods in the amount of at least four hundred thousand (400,000) rubles.
Check the current prices on the page http: //
If there is a promotion, some goods can be purchased at retail at wholesale prices, check this possibility with managers.

Properly selected basketball equipment is the key to success. Such equipment, which will be convenient in use and maintenance, is produced by our enterprise.

For professional competitions, full-sized shields made of silicate (tempered) glass are used. For sports clubs And training sessions plexiglass shields are suitable. School halls and outdoor areas are recommended to be equipped with shields made of laminated moisture-resistant plywood, which perfectly tolerates temperature extremes and precipitation. For training and streetball, training boards are used, which can be made of either plywood or plexiglass. The ring should spring forward.

basketball court

Basketball courts are structures with a special coating, markings and special equipment.

Basketball is played by two teams, each consisting of five players. The goal of each team is to throw the ball into the opponent's basket and prevent the other team from taking possession of the ball and throwing it into the basket. The basketball playing field must be a rectangular flat hard surface without any obstructions. For official FIBA ​​competitions, the dimensions of the playing area must be 28 meters long and 15 meters wide. The playing surface must be evenly and adequately lit. The two shields must be made of a transparent material (preferably tempered safety glass) made from a solid piece and having the same degree of hardness as shields made of 3 cm thick hardwood. The dimensions of the shields must be: 1.80 m (+ 3 cm) horizontally and 1.05 m (+ 2 cm) vertically. The front surface of the two shields should be smooth, the edges should be marked with a line. Shields must be rigidly mounted.

Detailed information about the products and prices of our company, in our.

GOST R 56434-2015

NATIONAL STANDARD OF THE RUSSIAN FEDERATION

Equipment for sports games

BASKETBALL EQUIPMENT

Functional requirements, safety requirements and test methods

Equipment for sports games. basketball equipment. Functional requirements, safety requirements and test methods

OKS 97.220.30

Introduction date 2016-07-01

Foreword

1 DEVELOPED by the Self-Regulatory Organization Non-Commercial Partnership "Industrial Association of National Manufacturers in the physical culture and sports "Promsport" (SRO "Promsport")

2 INTRODUCED by the Technical Committee for Standardization TC 444 "Sports and tourist products, equipment, inventory, sports and sports services"

3 APPROVED AND PUT INTO EFFECT by Order of the Federal Agency for Technical Regulation and Metrology dated June 15, 2015 N 652-st

4 This standard has been developed taking into account the main regulatory provisions of the European regional standard EN 1270:2005 * "Equipment for sports games - Basketball equipment - Functional requirements, safety requirements and test methods" (EN 1270:2005 "Playing field equipment - Basketball equipment - Functional and safety requirements, test methods", NEQ)
________________
* Access to international and foreign documents can be obtained by clicking on the link to the site http://shop.cntd.ru. - Database manufacturer's note.

5 INTRODUCED FOR THE FIRST TIME


The rules for the application of this standard are set out in GOST R 1.0-2012 (section 8). Information about changes to this standard is published in the annual (as of January 1 of the current year) information index "National Standards", and the official text of changes and amendments - in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the next issue of the monthly information index "National Standards". Relevant information, notification and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet (www.gost.ru)

1 area of ​​use

1 area of ​​use

This standard applies to basketball equipment. classes A-E. The standard specifies the functional requirements, safety requirements and test methods for basketball equipment.

This standard does not apply to basketball equipment for home use and basketball training equipment for practicing ball shooting.

Note - Training basketball equipment for practicing ball throws is used for teaching throwing. basketball ball Add to cart.

2 Normative references

This standard uses normative references to the following standards:

GOST 380-2005 Carbon steel of ordinary quality. Stamps

GOST 25552-82 Twisted and wicker products. Test Methods

Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and on issues of the monthly information index "National Standards" for the current year. If a dated referenced reference standard has been replaced, it is recommended that the current version of that standard be used, taking into account any changes made to that version. If the reference standard to which the dated reference is given is replaced, then it is recommended to use the version of this standard with the year of approval (acceptance) indicated above. If, after the approval of this standard, a change is made to the referenced standard to which a dated reference is given, affecting the provision to which the reference is given, then this provision is recommended to be applied without taking into account this change. If the reference standard is canceled without replacement, then the provision in which the reference to it is given is recommended to be applied in the part that does not affect this reference.

3 Requirements

3.1 Functional requirements

3.1.1 Classification of basketball equipment

Basketball equipment is classified by types and classes.

3.1.1.1 The classification of basketball equipment by type is given in Table 1.


Table 1 - Classification of basketball equipment by type

		Equipment Description
		Free-standing equipment with overall dimensions of 2250 mm and 3250 mm
		Free standing equipment of other dimensions
		Folding equipment
		Equipment fixed to the wall
		Ceiling Mounted Equipment
		Equipment, movable, with mounting sleeves
		Equipment fixed on the floor
		Equipment with height adjustment from 2600 to 3050 mm

3.1.1.2 The classification of basketball equipment by class is given in Table 2.


Table 2 - Classification of basketball equipment by class

	The width of the free space under the shield, im
	At least 3250
	At least 2250
	At least 1650
	At least 1200

An example of free space under the shield is shown in Figure 1.

Width of free space under the shield

Figure 1 - Example of free space under the shield

3.1.2 Materials and construction

3.1.2.1 A complete set of basketball equipment must consist of the following parts:

basketball backboard - 1 piece;

ring - 1 piece;

mesh - 1 pc.;

carrier truss;

stability device.

3.1.2.2 The installation height of the basket for basketball equipment of classes A-D is shown in Figure 2 and Table 3.

Figure 2 - Installation height of the basket for basketball equipment of classes A-D

Table 3 - Basket installation height for basketball equipment classes A-D

Type of basketball equipment	Nominal size
			Basketball backboard dimensions

3.1.2.3 The dimensions and markings of the basketball backboard are shown in Figure 3 and Table 4.

Note - The upper side of the ring is at the level of the upper edge line of the small square.

Figure 3 - Dimensions and markings of the basketball backboard

Table 4 - Basketball backboard dimensions and markings

Basketball backboard dimensions		Basketball backboard markings
All others	All others

3.1.2.4 The plate for attaching the rings of class A, B and C basketball equipment is shown in Figure 4.

Note - Requirements for fastening the rings of basketball equipment of classes D and E are not established.

Figure 4 - Plate for fixing rings of basketball equipment of classes A, B and C

When attaching a basketball backboard, do not use holes. Any other method of attaching the basketball backboard is allowed if safety requirements are met.

3.1.2.5 The dimensions of the basketball hoop are shown in Figure 5.

1 - ring mounting plate

Figure 5 - Dimensions of the basketball hoop

3.1.2.6 The basketball backboard is made of the following materials:

- tree;

- synthetic or mixed material;

- transparent synthetic material;

- safety glass;

- metal.

3.1.2.7 The hoop and backboard must be painted in contrasting colors. Recommended basketball backboard colors for class A basketball equipment are shown in Table 5.


Table 5 - Recommended Basketball Backboard Colors for Class A Basketball Equipment

Material name	Shield front color	The color of the markings on the front of the shield
Tree
Synthetic or mixed material
Transparent synthetic material	Transparent
Safety glass
Metal

3.1.2.8 The front side of the backboard facing the playing field must be smooth.

3.1.2.9 Class A and B basketball hoop

Rings must be made of carbon steel of ordinary quality grades not lower than St2sp, St2ps, St3ps, St3sp according to GOST 380.

The color of the ring should be orange.

On the underside of the ring, 12 evenly spaced elements must be welded to secure the mesh.

3.1.2.10 Net for basketball equipment classes A to D

Threads for weaving nets from which the net is made can be synthetic or natural.

The grid must be white.

The mesh must be made of threads for weaving nets with a breaking load of at least 1700 N in accordance with GOST 25552.

Threads for weaving nets must have a diameter of at least 4.5 mm.

When the net is attached to the ring, it should hang vertically from the hooks for attaching the net. The mesh length in this position is 400 mm.

The net must be made in such a way that when a ball with a diameter of 749-780 mm is thrown in, it experiences resistance when passing through the net, but does not get stuck. The passage of the ball over the net must be clearly visible.

3.1.2.11 Truss for basketball equipment classes A-D

For basketball equipment, the design of which allows adjustment of the height of a basketball backboard with a basket and a net, it is necessary to install locking devices at a height:

- 3050 mm - for playing basketball;

- 2600 mm - for playing mini-basketball.

After adjusting the height, the horizontal dimensions from the basketball backboard to playing field should not change.

3.2 Safety requirements

3.2.1 All corners and edges located in the free space of the playing field area at a height of up to 2900 mm and not protected by upholstery must have a radius of curvature of at least 3 mm or be made with a bevel.

The corners of the backboard must be beveled or protected with padding.

3.2.2 Ring

3.2.2.1 The hoop must be fixed to the truss in such a way that the force transmitted from the hoop does not act directly on the backboard (see Appendix A).

3.2.2.2 The hoop attachment plate must be designed so that it does not protrude beyond the bottom edge of the backboard.

3.2.2.3 Rings with shock absorbers shall comply with the following requirements:

- there should be no gaps between the bracket and the ring, in which the player's fingers can get stuck;

- the cushioning mechanism shall only operate when a static load of 1050 N is applied to the upper side of the hoop at the point farthest from the backboard in accordance with Annex B B.1;

- when the damping mechanism is actuated, gaps of more than 8 mm should not appear between the body of the damping mechanism and the device for its fastening in accordance with B.1 of Appendix B;

- when the damping mechanism is activated, the ring must not deviate downward from the initial horizontal position by more than 30° in accordance with B.1 of Appendix B;

- the value of residual deformation when testing the ring with a shock absorber in accordance with B.2 of Appendix B should be no more than 10 mm.

3.2.2.4 The value of permanent deformation of a rigidly fixed ring when tested in accordance with Annex B shall not exceed 10 mm.

3.2.3 Net attachment

3.2.3.1 The attachment of the net to the ring must be done in such a way that the player's finger cannot get stuck. The gaps should not be more than 8 mm. An example of hooks for attaching the mesh is shown in Figure 6.

Figure 6 - An example of hooks for attaching the net

3.2.4 Height adjustment and storage device

3.2.4.1 A device for adjusting the height of a basketball backboard and for storage must be designed to prevent inadvertent adjustment during operation.

3.2.4.2 The person who makes the adjustment using such a device must be able to observe both the adjustment mechanism and the backboard during the adjustment process.

3.2.5 Upholstery

3.2.5.1 Basketball backboards for Class A and B basketball equipment must be upholstered as follows:

- upholstery should cover the bottom edge and sides of the basketball backboard at a distance of up to 350 mm from the bottom edge and side edges;

- the front and back sides must be covered with upholstery at a distance of at least 20 mm from the bottom edge (see figure 7).

3.2.5.2 The requirements for the presence of upholstery on elements of basketball equipment of classes A and B are given in Table 6.


Table 6 - Presence of upholstery on elements of basketball equipment of classes A and B

	Elements of basketball equipment
	basketball backboard
		Backside
Note - "X" - the requirement is mandatory, "(X)" - the requirement is advisory.

3.2.5.3 Upholstery of uprights shall be made as follows (see Figure 7):

- each post of the basketball backboard located within 1200 mm behind the playing side of the backboard must be upholstered at a distance of at least 2750 mm from the floor;

- for type 1 basketball equipment, the side of the truss that faces the free space in the field of play must be padded at a distance of 2150 mm from the surface of the field of play.

NOTE For Class A basketball equipment, provision should be made for padding on those sides of the uprights which, although in the free space zone, are close enough to constitute a potential hazard. A

Figure 7 - Upholstery of basketball backboards and racks

3.2.6 Free space under the shield

The free space under the shield must be free from obstructions.

3.2.7 Strength

3.2.7.1 When testing the strength of a basketball backboard in accordance with Appendix D, after removing the concentrated horizontal load, the residual horizontal deviation from the zero position must not exceed 10 mm.

3.2.7.2 When testing the strength of a basketball hoop intended for use in the hall, according to Appendix D, after removing the concentrated horizontal load, the residual horizontal deviation from the zero position should not exceed 10 mm.

3.2.7.3 When testing the strength of a basketball hoop intended for outdoor use, according to Appendix D, after removing the concentrated horizontal load, the residual horizontal deviation from the zero position should not exceed 10 mm.

3.2.8 Sustainability

When testing for stability according to Appendix E, after removing the concentrated vertical load, the residual vertical deviation from the zero position should not exceed 10 mm.

4 Test methods

4.1 The requirements in accordance with Section 3 are checked visually, organoleptically or by instrumental methods.

4.2 Visual inspection of the ring - according to Appendix A.

4.3 Tests of the ring with a shock absorber - according to Appendix B.

4.4 Tests of a rigidly fixed ring - according to Appendix B.

4.5 Strength tests - according to Appendix D.

4.6 Stability tests - according to Appendix D.

4.7 Based on the test results, a report or protocol is drawn up.

5 Instructions for assembly, installation and maintenance

The manufacturer, together with the basketball equipment, must provide instructions for assembly, installation, adjustment and maintenance.

6 Information plate

The equipment must be affixed with a label bearing one of the following inscriptions:

"Basketball equipment is designed solely for its intended use."

"Do not hang on the net of the basketball hoop!".

Note - Instead of a plate with text, it is possible to use suitable graphic materials.

7 Equipment marking

Equipment must be marked with the following:

- the designation of this standard;

- name or trademark of the manufacturer;

- information plate in accordance with section 6.

Annex A (mandatory). Visual inspection of the ring

Annex A
(mandatory)

A.1 Essence of the method

A.1.1 By visual inspection of the hoop, it is determined whether the force transmitted from the hoop is acting directly on the backboard.

A.1.2 As a result of inspection, it must be established that the hoop is fixed to the truss in such a way that the force transmitted from the hoop does not act directly on the backboard.

Annex B (mandatory). Shock absorber ring test

Annex B
(mandatory)

B.1 Single load test

B.1.1 Essence of the method

During the test, a static load of (1500 ± 50) N is applied to the front edge of the ring for (5 ± 1) s.

In the state of loading, the rings register:

the presence of gaps between the body of the shock-absorbing device and the device for attaching the ring of more than 8 mm;

deviation of the ring at an angle of more than 30 °.

After removing the load, check the return of the ring to its original position.

B.1.2 Apparatus

The loading device must provide a concentrated vertical load of (1500 ± 50) N for (5 ± 1) s.

The load application scheme is shown in Figure B.1.

Figure B.1 - Scheme of load application when testing a ring with a shock absorber with one load

B.1.3 Procedure

B.1.3.1 Apply a static load of (1500 ± 50) N to the front edge of the ring for (5 ± 1) s.

B.1.3.2 In the state of loading, the rings are recorded:

- the presence of gaps between the body of the shock-absorbing device and the device for attaching the ring of more than 8 mm;

- deviation of the ring at an angle of more than 30°.

B.1.3.3 After removing the load, the return of the ring to its original position is recorded.

B.2.1 Essence of the method

During the test, a static load of (1500 ± 50) N is applied to the front edge of the ring.

In the state of loading of the ring (after deflection), an additional load of (2400 ± 50) N is applied for (60 ± 1) s.

B.2.2 Apparatus

The loading device must provide a concentrated vertical load of (1050 ± 50) N, and then, after deflection of the ring, a concentrated vertical load of (2400 ± 50) N for (60 ± 1) s to the front edge of the ring.

The load application scheme is shown in Figure B.2.

Figure B.2 - Scheme of load application when testing a ring with a shock absorber with two loads

B.2.3 Procedure

B.2.3.1 When testing a ring with a shock absorber, a static load of (1050 ± 50) N is applied to the front edge of the ring. In the state of loading of the ring (after deflection), an additional load of (2400 ± 50) N is applied for (60 ± 1) s.

B.2.3.2 After removing the load, a residual deformation of more than 10 mm is recorded, as well as the presence of damage, incl. cracks, breakages, weakening of connections and connections.

Annex B (mandatory). Rigid Ring Tests

Annex B
(mandatory)

B.1 Nature of the method

When testing a rigidly fixed ring, a static load of (2400 ± 50) N is applied to the front edge of the ring for (60 ± 1) s.

After removing the load, a residual deformation of more than 10 mm is recorded, as well as the presence of damage, incl. cracks, breakages, weakening of connections and connections.

B.2 Apparatus

The loading device must provide a concentrated vertical load of (2400 ± 50) N for (60 ± 1) s, applied to the front edge of the ring. The load application diagram is shown in Figure B.1.

Figure B.1 - Scheme of applying a load to a rigidly fixed ring

B.3 Procedure

B.3.1 Apply a static load of (2400 ± 50) N for (60 ± 1) s.

B.3.2 After the load is removed, a residual deformation of more than 10 mm is recorded, as well as the presence of damage, incl. cracks, breakages, weakening of connections and connections.

Annex D (mandatory). Strength testing of basketball equipment

Annex D
(mandatory)

D.1 Essence of the method

When testing, depending on the type of basketball equipment, a concentrated horizontal load is applied (see Table D.1):








Table D.1 - Applied loads depending on the type of basketball equipment

Note - "X" - application of the load is mandatory, "(X)" - application of the load is advisory.

After removing the load, the shield and basket are inspected and any residual deformations are recorded.

D.2 Apparatus

The loading device must provide:

- concentrated horizontal load of (900±20) N applied to the shield for (60±5) s;

- concentrated horizontal load of (900 ± 20) N applied to the basket for (60 ± 5) s for equipment installed in the halls;

- a concentrated horizontal load of (100 ± 20) N applied to the basket for (60 ± 5) s for equipment installed outdoors.

The load application scheme is shown in Figure D.1.

Figure D.1 - Scheme of application of loads during strength tests of basketball equipment

D.3 Procedure

D.3.1 When testing, depending on the type of basketball equipment, a concentrated horizontal load is applied (see Table E.1):

- value (900±20) N for (60±5) s - to the shield;

- value (900±20) N for (60±5) s - to the basket of equipment installed in the halls;

- with a value of (1000±20) N for (60±5) s - to the basket of equipment installed outdoors.

D.3.2 After removing the load, inspect the shield and the basket and record all residual deformations.

The equipment must not be damaged, incl. cracks, breakages, excessive residual deformations, weakening of connections and bonds.

Annex D (mandatory). Stability tests

Annex D
(mandatory)

E.1 Essence of the method

When testing for resistance to the middle of the backboard of basketball equipment of all types, a concentrated vertical load of (3200 ± 50) N is applied for (60 ± 5) s.

During the test, all residual deformations are recorded.

E.2 Apparatus

The loading device must provide a concentrated vertical load of (3200 ± 50) N applied to the middle of the shield for (60 ± 5) s.

The load application diagram is shown in Figure D.1.

Figure E.1 - Scheme of load application during stability tests

E.3 Procedure

E.3.1 A concentrated vertical load of (3200 ± 50) N is applied to the middle of the backboard of basketball equipment of all types for (60 ± 5) s.

E.3.2 After removing the load, inspect the shield and basket and record all residual deformations.

After testing, the structures must not be damaged, incl. cracks, breakages, excessive residual deformations, weakening of connections and bonds.

UDC 796.022:006.354	OKS 97.220.30
Keywords: basketball equipment, functional requirements, safety requirements, test methods

Electronic text of the document
prepared by Kodeks JSC and verified against:
official publication
M.: Standartinform, 2015