The technique of winding fishing line on a reel. How to properly assemble a spinning tackle How to correctly install a fishing line on a spinning reel

This is a fairly simple action that any beginner can do. Necessary unscrew the mount And insert coil in a special holder on the spinning handle. After that it is necessary tighten the ring so that it presses the base of the coil. Tighten it tightly so that the coil does not hang out.

However, do not apply excessive force so as not to strip the thread, which is made of plastic.

How to wind a fishing line

To do this, you must perform the following steps.

Pull the tip of the line through the rings of the spinning rod, starting with the smallest one located at the top of the rod.
Fold out the line guide ring and tie the line to the spool. This is best done with a special self-tightening knot.
To make it, you need to make a double loop and tighten it on the spool. The protruding tip of the fishing line must be cut off.
Next, you need to properly wind the fishing line on the spool. To do this, you need to create a slight tension. It is convenient to wind the line together with a partner who holds the reel of line in his hands and controls the resistance. If there is no assistant, you can do it yourself by putting the coil in your pocket.
You can also pass the line through the fingers of the hand with which you hold the spinning rod, and with the other turn the handle of the reel.
It is also not worth creating excessive tension, as this is fraught with the formation of knots and uneven winding.
It is recommended to wind the fishing line without stopping and constantly monitor the process.
The winding process must be completed at the moment when approximately 25-30 millimeters remain to the edge of the spool. This is considered its optimal filling. It is not recommended to reel in more lines, as this can create some problems (the appearance of knots, the line jumping off the spool when casting).

Helpful advice! After the end of fishing, you need to make one idle cast. In it, raise the rod perpendicular to the ground, and slowly rotate the reel handle to wind the line. This will allow it to dry and lay correctly on the spool. A nice bonus in such cases can be a bite, which happens quite often!

How to set up

This is probably the main point in pre-setting your spinning rod. A lot will depend on it.

Correctly tuned coil prevent line breakage And allows you to catch big fish.

Almost all inertialess reels are equipped with a friction brake, which allows you to adjust the force.

At a certain load, the spool begins to scroll and bleed the line. This is necessary to "extinguish" the jerks of large fish.

There are two types of regulator location - on top of the spool and on the bottom of the reel. The second option is practically not used in new models, although it is quite common among spinners.

It is necessary to adjust the clutch based on the breaking force of the fishing line. For example, if it can withstand real 7 kilograms, then the friction brake must be adjusted to 4-5 kg. This will allow, in the event of a jerk of a fish with a capacity of 7-8 kilograms, to keep the fishing line safe and play it into the reservoir under the pressure of a predator. To do this, it is necessary to fill the spool completely.

3 ways to increase your fish catch

There are many ways to increase your fish catch, but the most effective ones are the ones. Below, the editors of the site share with you the 3 most effective ways catch increase:

. This is a pheromone-based supplement that activates receptors in fish. ATTENTION! Rybnadzor wants to ban this bait!
Less effectively work out any other bait with flavors, it is better if they contain pheromones. But it's best to use novelty 2016 — !
Learning different fishing techniques. For example, it is written about spinning postings.

For adjustment, you can use weights from conventional scales that are hung on the end of the fishing line. Experienced anglers set up the drag a little differently. This can be done while fishing.

Fully equip the spinning rod and hang a lure on it.
Hook it to a tree or other object.
Step back 5-10 meters and pull the spinning in such a way as if you were playing a fish.
Apply maximum tension to the tension (the rod should bend into an arc), and gradually release the clutch until the ratchet is activated.
Don't pull too hard, as you can break the rod.

As you can see, there is nothing complicated in attaching the reel to the rod and setting it up, and any beginner will have to follow these steps.

But, it is very difficult to overestimate their importance, since success in fighting a large trophy may depend on this. Good luck fishing!

How to wind the fishing line on the spool, see the video. Enjoy watching!

One of the main factors influencing the success of fishing is the degree of preparation for it. Ideal weather do not guarantee the effectiveness of fishing, if fishing gear not configured properly. Preparation includes:

The correct location of fishing accessories relative to each other to ensure comfortable fishing.
Preparation of baits and bait mixtures.
Rod tuning - equipment, installation of fishing reels and equipment.

An important point in the preparation is the correct winding of the main line on the spool of the fishing reel. Compliance with the winding technique will ensure the correct discharge of the line when casting, and prevent it from breaking.

Features of winding fishing line on a reel

Why is proper winding necessary?

First of all, the quality of the winding greatly affects the casting distance: the ideal winding will be one that provides close to the maximum range corresponding to technical specifications coils.
Winding also has a great influence on the life of the fishing line. For example, if the level of the top layer exceeds 3 mm from the side of the spool, then the fishing line, due to physical friction, will have greater mechanical wear. If this level coincides with the edge, uncontrolled discharges will occur, which will lead to the appearance of a "beard" and the need to cut the line.

Connecting line to spool

The first step in equipping the reel with fishing line is to attach the line to the spool. Many anglers don't anchor the line in the hope that the bottom layers won't be used, but that's not exactly the right approach. Over time, the top working layer will wear out and gradually shorten. There are many ways to bind, but the most common is a specially designed knot and a self-tightening loop:

Special knot very much like a clinch. Its advantage is that it practically does not stretch and holds perfectly.
Self-tightening knot has a slight stretch, but under the action of the tension of the fishing line, it will continue to tighten until it stops.

It is desirable to fasten the fishing line or cord at the bottom of the spool, this will reduce the amount of contact between the knot and the unwinding turns.

Backing (winding)

Thanks to advances in technology, modern fishing lines are produced thinner in diameter without loss in strength, therefore very often the length of the reeled line is much less than the capacity of the spool. In this case, there is a need for something to fill the free space. Some anglers fill it with electrical tape or nylon thread. These methods are not very good, because over time the tape peels off the glue that holds the lower layers of the fishing line together, and the nylon thread dries for a very long time if it gets wet while fishing. The best option was invented by American anglers: to wind a cheaper fishing line into the lower layer, and then tie the main one of better quality to it. The bottom layer is called backing, in our country it is better known as winding.

Backing is an inexpensive fishing line with a diameter of up to 0.3 mm. It is not recommended to use a thicker fishing line, as it will deform the main layer. The winding length can only be determined experimentally. This will require additional spool. First, the available amount of the main fishing line is wound on it, then backing. After that, the winding is shortened to the required size after filling the spool. Winding on the main coil takes place in reverse order: the backing segment is wound up first, then the main component.

Taper profile

Different fishing reels apply coils of line to the spool in different ways. There are three types of winding:

Cylindrical.

Trapezoidal.

Chaotic.

The first two types correspond to expensive well-known manufacturers. The coils lay flat and in a row. The latter is inherent in cheap Chinese fakes. Technical flaws in such reels can ruin fishing, and it is better to refuse them. It is impossible to radically deal with the negative effects of winding, since the spool stroke is structurally provided for by each manufacturer. But to some extent it is quite possible to improve the winding. For this, the mirror method is used. That is, in those places where the coil leaves depressions, hills are made, and vice versa. This process is very painstaking, and it is done only by hand. Thus, uneven stacking of turns is compensated by manual stacking of anomalous segments, and the winding acquires the necessary taper.

In its turn, trapezoidal winding has two types of taper: forward and reverse.

A straight cone is formed if the technical feature of the coil provides for laying turns with a decrease in pitch towards the spool wall. Such a cone ensures minimal friction of the turns during reset. With a reverse taper, the pitch gradually decreases towards the side of the spool. The friction of the turns with such a cone is greater, but the probability of spontaneous discharge of the fishing line is reduced.

Winding line on a spinning reel

The winding of the fishing line on the spinning reel is carried out in the following order:

The reel is fixed on the spinning rod in the reel seat.
The spinning of the telescopic structure must be decomposed into working condition. It is not necessary to assemble the plug rod, it is enough to manipulate its lower part.
The fishing line is inserted starting from the topmost, small, ring towards the reel.
The fishing line is attached in a knot to the bottom of the spool with the line stacker folded down.
After fixing, the line stacker is lowered into working condition and the fishing line is wound by rotating the reel handle.

It must be remembered that winding is carried out with the obligatory tension of the line. To do this, it is enough to press the fishing line to the blank of the rod with one hand at a distance of 35-40 cm from the reel.

Storing line on a reel

An important condition for the long-term operation of the scaffold is proper storage. Forest care is necessary both after each fishing trip and during the off-season.

When preserving the coil for the winter, it is necessary:

Completely remove the line from the spool. Bucking can not be touched.
Dry wood thoroughly. IN this case a hair dryer would be very helpful.

After each fishing, it is not necessary to dry the forest along the entire length, it is enough to process the segment of the maximum cast.

After drying, the fishing line is wound back onto the spool with a slight tension. At the opening of the season, it will need to be rewound again with a lot of tension. For a long time, it is better to keep the coil in the newspaper: it will take the remaining moisture from the winding and prevent minor damage to the cone. The monofilament is afraid of ultraviolet radiation, so the storage place must be not only dry, but also dark. For greater safety, the fishing line can be treated with fat or glycerin.

Finally, a few tips to help wind the fishing line perfectly:

When winding the line on the spool, it is necessary to pay Special attention the first few turns. They give direction to the rest of the winding, so they must be laid with special care.
To tension the line when winding, it is very convenient to use a small book, skipping the line between the pages. The book will prevent your hands from getting hurt and straighten uneven areas.
When winding a new line, it needs to be wetted a little. It will gain more flexibility, will twist less, preventing the formation of a "beard".
When using braided line, place a small piece of fabric on the spool to prevent the entire cone from sliding over its surface.

In this article, we will consider how to wind a line on a spool. 100 meters of fishing line with a thickness of 0.3 mm is wound on a standard reel. It is calculated that the winding of the line on the reel is usually wound 2 mm below the edge of the bobbin collar.

More than the edge of the side, the winding of the fishing line on the reel is not performed; at the moment of casting, the fishing line is guaranteed to break the turns and form a beard. The lower the line is wound on the reel, but the lower it is, the shorter the casting distance.

Professionals suggest winding braids of 250 meters each, but it’s easier to wind up additional fishing line to solve the problem - it’s cheaper and the effect is greater (see article: ““). At first, I tried to make different formulas to calculate the length of the winding line, but, firstly, it did not work out with the required accuracy, and secondly, this length is determined automatically during the experimental winding of the fishing line on the reel.

The reel designers, as a result of experiments, have revealed a certain improvement in casting performance in relation to the winding profile.

The narrowing of the winding towards the tulip (front cone) is embodied in the Long Cast spool, which really enhances the casting distance and is used in carp, float and feeder fishing.
The narrowing of the winding to the handle (rear cone) is made in the ABS spool from "Daiva", which increases the casting distance, and most importantly - greatly reduces the possibility of dropping loops, as well as "beards" when fishing spinning wiring jerky. For spinning players fishing with twitching, jigging and jerking, such winding of fishing line on the reel is simply a must. Use this winding on a braid with a diameter smaller than 0.2 mm. From cone windings, direct winding gives similar results.

Winding experiments

For reels from Daiwa and Abu Garsia, as well as the well-known in Ukraine inexpensive Cobra, the winding style is formed by the taper of the spool. Shimano has taken a unique approach to adjusting the profile by adding washers under the spool.

The downside of the system with washers is the impossibility of using it in more well-known and convenient reels with a rear brake. Any winding profile can be set at the time of backing winding.

Winding fishing line: scheme

Having installed the reel on the rod, we first wind the main line with the help of the reel.
Next, remove the spool and tie the backing and main line with a reliable knot.
Next, hold the spool with your left hand, little by little, scrolling towards the winding, wind the backing with your right hand.
When winding, gradually organize any profile, in particular ABS. The height of the cone must be large - approximately 1.5 -2.5 mm. In general, this is a matter of your experience, in particular, K. Kuzmin, who is familiar to everyone, writes: “ It is necessary to raise the angle of the cone in case of constant reset of the loops».
Now you need to turn the scaffold backing down, and the base up. If there is a guarantee that no one will climb into the loops of the fishing line with their feet, then the forest can be spread out on the floor of the apartment, creating large loops. Then, tying the backing on the spool, make a working winding.

I do my work entirely by hand. I form a reverse cone from the first turns and adhere to a similar profile at all stages of winding. As a result of this approach, after casting, your reel will independently fold the line according to a given profile when reeling.

Warning

Although, a caveat must be made that as a result of all these rewinds, the line is twisted and often requires unwinding. The main thing is that the reel has an anti-twisting line roller. A swivel was tied in front of the feeder. Such a pair will spin any level of twist automatically, practically, in a couple of casts.

Consider a device for winding fishing line. It consists of the following elements:

nail;
and a circle of rubber 7.5 mm thick.

The nail is taken of such a size that it would go into the hole of the spool almost closely. It would be nice to have a stem from similar coils (only faulty ones). In the absence of such, you can rivet the nail itself a little, creating a slightly elliptical configuration for it along the hole in your spool. We pierce the rubber in the center with a nail.

Then we insert it into the spool, and take an electric drill or a screwdriver and clamp this device in the drill chuck. In order to better bind and increase the friction force between the rubber band and the spool, we slightly tap on the nail, drowning it in rubber (you can also use “micropork”). We knit the fishing line on the spool with a self-tightening knot, and then tighten the knot, wind it clockwise, hold the bobbin with the fishing line in one hand, by the central hole, take the drill in the other hand and, adjusting the speed of the cartridge, we wind it.

It is not necessary to wind the line strongly, we only control the uniform laying of the line along the spool, leading the line up and down

We fill almost the entire spool, leaving a shoulder of 1.35 - 2.35 mm; with a denser winding, the forest can sometimes be thrown off the spool. With such winding, the twisting of the fishing line does not occur. On the water, the fishing line looks aesthetically pleasing and even, and in this case it lasts much longer.

Video lesson “How to wind a fishing line on a reel”

Conclusion

I hope that guided by the advice of this article, you will be able to properly wind the line on the reel of your rod. Good luck!

Predatory fish are mainly caught on spinning. And in addition, spinning fishing involves constant movement and change of lures, which makes it more exciting. Therefore, spinning fishing is preferred by most anglers.

Those who are just beginning to learn the intricacies of this art do not always know how to properly equip a spinning rod so that fishing brings not only pleasure, but also good prey. Indeed, despite the simplicity, such fishing has many nuances that you need to know.

What is spinning

Among the main elements of spinning are such as:

Directly a spinning rod equipped with access rings;
a reel for fixing the fishing line (there are inertia-free or multiplier);
fishing line (also use a braided cord);
· leash;
artificial bait.

All these details have their own functions, which, one way or another, affect the reliability and functionality of the tackle in general.

Main characteristics

High quality spinning gear and, accordingly, fishing depends on the following characteristics: test load, length and action (or response to load). Also, not a key, but an important role is played by the material from which the rod and the design of the handle are made.

Test load

According to this characteristic, the weight range of lures is determined, which is recommended for a particular rod. . Spinning rods are divided according to this characteristic into several types:

There is also several not so common types of rods according to the test load:

Ultra Light, or ultra-light class allows a load of no more than 10 grams.
Medium Light (medium light class) - the load level ranges from 5 to 25 grams.
Medium Heavy, or medium-heavy class - the allowable weight of artificial bait is from 15 to 40 grams.

Professionals recommend choosing a rod with a test load of 12 to 15 grams, if a light bait is used, then the rod test can be 8 - 10 grams. In this case, you should not go beyond the test load. If you use a heavier bait, then the rod may break, and it will be much harder to drive such a bait. If the bait is too light, it will be difficult to cast it for a considerable distance.

This is also an important characteristic on which the results of fishing depend. Measured mostly in meters, it is also possible to meet inches or feet. The length is calculated depending on the fishing conditions, the required casting distance and other factors. Wherein there are several types of spinning based on this feature:

Types of building

Action is the ability to bend a rod relative to the resulting load or resistance. Distinguish fast (under load bends only top part rods), medium (during the load, the rod bends up to half) and slow action (the majority of the rod is subjected to the load).

This characteristic is selected depending on the needs. For example, for perch fishing, light rods are often used - in order to cast the bait much further. But mainly rods with a medium action are used, as they are more versatile.

Material for manufacturing

They make spinning rods in most cases from various materials, including the following:

The choice of material from which the rod is made should be made based on the conditions and purpose of fishing.

Spinning handle

The handle is also an important part of spinning., which is made mainly from natural cork, leather and rubber.

There are two types of handles: solid and spaced apart (there are gaps throughout the handle design designed to lighten the rod). There are also single-handed and two-handed handles.

The type of handle does not have a big role in catching fish, but the long handle makes it easier to cope with the most crucial moment of fishing - playing.

At the bottom of the handle, with the help of a holder, a coil is attached.

How to choose the right coil

There are two types of reels for winding fishing line: inertialess (during the cast, the spool does not move at all) and multiplier (the spool rotates during the casting of the fishing line). Professional anglers recommend using the first option, as they have greater sensitivity and casting distance. They are also much cheaper than cartoons.

Among the characteristics are the following:

Having dealt with all the characteristics, you can understand how to properly use the inertialess coil.

Spinning line

For fishing with spinning, braided or monofilament line is usually wound on the reel. Among the advantages of monofilament fishing line it is worth noting the following:

It is very conveniently laid in the spool;
extremely rarely twists;
very soft and elastic, which has a bad effect on the sensitivity of the bite.

This type of fishing line also has its drawbacks., which sometimes do not allow spinning to work normally:

not strong enough, so it often breaks under heavy loads;
Due to its elasticity, its service life is rather short.

Experienced anglers prefer braided line, despite the fact that it is much more expensive than monofilament. This is because the braid is much stronger and less stretchy, making it more susceptible to bites.

The scheme for winding fishing line on a reel is very simple. And it consists of just a few steps that answer all the questions of novice anglers about how to properly wind the line on the spinning reel.

First of all, you need to know how much line to put on the reel. Experienced anglers recommend to put on the line almost to the very end of the reel, leaving only a couple of millimeters. Further directly about the winding process itself:

These steps will help you figure out how to properly wind the fishing line on spinning coil. With multipliers, the situation is a little more complicated, therefore, in order to do everything right, it is better to watch video tutorials.

Leash for fishing line

Fishing with a spinning rod in itself implies hunting for a predator. Therefore, in order to fully equip the spinning, it is necessary to attach a leash to the fishing line. This is done so that the predator could not bite the main fishing line with sharp teeth.

Three types of leashes are made:

The leash is attached to the fishing line using a conventional fishing knot which can be done by following the instructions below:

you need to wind the fishing line onto the swivel using the rotation of the eye;
the free end of the fishing line is threaded into the resulting loop;
tighten the finished knot.

The choice of bait must be made taking into account that each bait is selected for a certain type of fish and fishing conditions. Below are most popular bait.

Types of rigs

If you know all types of equipment, then even a novice angler will be able to correctly assemble a spinning rod for fishing.

All these types of rigs are used for fishing predatory fish. At the same time, for each fish, different kind spinning, equipment and bait. Knowing all these nuances, even a beginner in spinning fishing will be able to properly equip spinning.

Attention, only TODAY!